Tolerances for
Spherical Plain Bearings |
1.Symbol
d: Bearing bore diameter of shank diameter, nominal.
dmp: Single plane mean bore diameter of shaft diameter deviation.
Vdp :Bore diameter variation in a single radial plane.
Vdmp: Mean bore diameter variation.
Bs: Deviation of a single width of the inner ring.
B: Vidth of inner ring, nominal.
D: Bearing outside diameter or housing washer outside diameter, nominal.
Dmp: Single plane mean outside diameter deviation.
Cs: Deviation of a single width of the outer ring.
C: Width of outer ring, nominal.
Ts: Actual diviation of width of the angular contact spherical plain
bearing.
Hs: Actual deviation of height of the spherical plain thrust bearing.
hs:his:Centre height deviation of rod ends of ball joint rod ends.
|
2.Spherical plain radial bearings
Inner ring
d over incl mm
|
-
|
10
|
18
|
30
|
50
|
80
|
120
|
150
|
180
|
250
|
315
|
400
|
10
|
18
|
30
|
50
|
80
|
120
|
150
|
180
|
250
|
315
|
400
|
500
|
dmp um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-8
|
-8
|
-10
|
-12
|
-15
|
-20
|
-25
|
-25
|
-30
|
-35
|
-40
|
-45
|
Vdp um
|
8
|
8
|
10
|
12
|
15
|
20
|
25
|
25
|
30
|
35
|
-
|
-
|
Vdmp um
|
6
|
6
|
8
|
9
|
11
|
15
|
19
|
19
|
23
|
26
|
-
|
-
|
Bs um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-120
|
-120
|
-120
|
-120
|
-150
|
-120
|
-250
|
-250
|
-300
|
-350
|
-400
|
-450
|
Outter ring
d over incl mm
|
10
|
18
|
30
|
50
|
80
|
120
|
150
|
180
|
250
|
315
|
400
|
500
|
630
|
18
|
30
|
50
|
80
|
120
|
150
|
180
|
250
|
315
|
400
|
500
|
630
|
800
|
dmp um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-8
|
-9
|
-11
|
-13
|
-15
|
-18
|
-25
|
-30
|
-35
|
-40
|
-45
|
-50
|
-750
|
Vdp um
|
10
|
12
|
15
|
17
|
20
|
24
|
33
|
40
|
47
|
53
|
60
|
-
|
-
|
Vdmp um
|
6
|
7
|
8
|
10
|
11
|
14
|
19
|
23
|
26
|
30
|
34
|
-
|
-
|
Cs um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-240
|
-240
|
-240
|
-300
|
-400
|
-500
|
-500
|
-500
|
-700
|
-800
|
-900
|
-1000
|
-1100
|
3.Angular contact spherical plain
bearings
Inner ring and width of bearing
d over incl mm
|
-
|
30
|
50
|
80
|
120
|
180
|
30
|
50
|
80
|
120
|
180
|
200
|
dmp um
|
0
|
0
|
0
|
0
|
0
|
0
|
-10
|
-12
|
-15
|
-20
|
-25
|
-30
|
Vdmp um
|
8
|
9
|
11
|
15
|
19
|
23
|
Bs um
|
0
|
0
|
0
|
0
|
0
|
0
|
-100
|
-120
|
-150
|
-200
|
-300
|
-400
|
Ts um
|
+150
|
+150
|
+200
|
+250
|
+350
|
+350
|
-300
|
-400
|
-500
|
-600
|
-700
|
-800
|
Outer ring
d over incl mm
|
-
|
30
|
50
|
80
|
120
|
150
|
180
|
250
|
30
|
50
|
80
|
120
|
150
|
180
|
250
|
315
|
Dmp um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-11
|
-14
|
-16
|
-18
|
-20
|
-25
|
-30
|
-35
|
Vdmp um
|
8
|
11
|
12
|
14
|
15
|
19
|
23
|
26
|
Cs um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-240
|
-240
|
-300
|
-400
|
500
|
-500
|
-600
|
-700
|
4.Spherical plain thrust bearings
Shaft washer and height of bearing
d over incl mm
|
10
|
18
|
30
|
50
|
80
|
100
|
120
|
180
|
18
|
30
|
50
|
80
|
100
|
120
|
180
|
200
|
Dmp um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-8
|
-10
|
-12
|
-15
|
-20
|
-20
|
-25
|
-30
|
Vdmp um
|
6
|
8
|
9
|
11
|
15
|
15
|
19
|
23
|
Bs um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-120
|
-120
|
-120
|
-150
|
-200
|
-200
|
-300
|
-400
|
Hs um
|
+150
|
+15
|
+200
|
+250
|
+300
|
+350
|
+350
|
+350
|
-300
|
-400
|
-500
|
-600
|
-700
|
-700
|
-700
|
-800
|
Housing washer
d over incl mm
|
-
|
30
|
50
|
80
|
120
|
150
|
180
|
250
|
315
|
30
|
50
|
80
|
120
|
150
|
180
|
250
|
315
|
400
|
Dmp um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-9
|
-11
|
-13
|
-15
|
-18
|
-25
|
-30
|
-25
|
-40
|
Vdmp um
|
7
|
8
|
10
|
11
|
14
|
19
|
23
|
26
|
30
|
Cs um
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
0
|
-240
|
-240
|
-300
|
-400
|
-500
|
-500
|
-600
|
-700
|
-800
|
5.Ball joint rod ends
Shank or housing of ball
joint |
Rings of ball joint housing |
d over incl mm
|
-
|
6
|
10
|
18
|
6
|
10
|
18
|
30
|
dmp
|
0
|
0
|
0
|
0
|
-30
|
-36
|
-43
|
-52
|
his
|
+800
-1200
|
|
d over incl mm
|
10
|
18
|
30
|
18
|
30
|
50
|
Dmp
|
0
|
0
|
0
|
-27
|
-33
|
-39
|
Cs
|
+100
-100
|
|
|
Radial Internal
Clearance of Spherical Plain Bearigs |
1.Spherical plain bearing
Series E,EW,EM
d over incl mm
|
-
|
12
|
20
|
35
|
60
|
90
|
140
|
160
|
240
|
12
|
20
|
35
|
60
|
90
|
140
|
160
|
240
|
315
|
C2 min Group C2 max um
|
8
|
10
|
12
|
15
|
18
|
18
|
18
|
18
|
18
|
32
|
40
|
50
|
60
|
72
|
85
|
100
|
100
|
110
|
Group normal min max um
|
32
|
40
|
50
|
60
|
72
|
85
|
100
|
100
|
110
|
68
|
82
|
100
|
120
|
142
|
165
|
192
|
192
|
210
|
Group C3 min max um
|
68
|
82
|
100
|
120
|
142
|
165
|
192
|
192
|
214
|
104
|
124
|
150
|
180
|
212
|
245
|
284
|
284
|
318
|
Series G
d over incl mm
|
-
|
10
|
17
|
30
|
50
|
80
|
120
|
160
|
220
|
10
|
17
|
30
|
50
|
80
|
120
|
160
|
220
|
280
|
C2 min Group C2 max um
|
8
|
10
|
12
|
15
|
18
|
18
|
18
|
18
|
18
|
32
|
40
|
50
|
60
|
72
|
85
|
100
|
100
|
100
|
Group normal min max um
|
32
|
40
|
50
|
60
|
72
|
85
|
100
|
100
|
110
|
68
|
82
|
100
|
120
|
142
|
165
|
192
|
192
|
210
|
Group C3 min max um
|
68
|
82
|
100
|
120
|
142
|
165
|
192
|
192
|
214
|
104
|
124
|
150
|
180
|
212
|
245
|
284
|
284
|
318
|
Series F
d over incl mm
|
-
|
12
|
20
|
35
|
55
|
80
|
120
|
12
|
20
|
35
|
55
|
80
|
120
|
150
|
Group normal min max um
|
32
|
40
|
50
|
60
|
72
|
85
|
100
|
68
|
82
|
100
|
120
|
142
|
165
|
192
|
Series Z,WZ
d over incl mm
|
-
|
15.875
|
50.8
|
76.2
|
152.4
|
203.2
|
254
|
15.875
|
50.8
|
76.2
|
152.4
|
203.2
|
254
|
304.8
|
Group normal min max um
|
50
|
80
|
100
|
130
|
180
|
200
|
230
|
150
|
180
|
200
|
230
|
300
|
330
|
350
|
Series GZ
d over incl mm
|
-
|
12.7
|
44.45
|
69.85
|
12.7
|
44.45
|
69.85
|
139.7
|
Group normal min max um
|
50
|
80
|
100
|
130
|
150
|
180
|
200
|
230
|
2.Rod Ends
Series E,EW
d over incl mm
|
-
|
12
|
20
|
35
|
60
|
12
|
20
|
35
|
60
|
80
|
Group normal min max um
|
23
|
30
|
37
|
43
|
55
|
68
|
82
|
100
|
120
|
142
|
Series
P,ZP |
Series
ZJ |
d over incl mm
|
-
|
30
|
Group normal min
max um
|
0
|
35
|
|
d over incl mm
|
-
|
8
|
14
|
20
|
35
|
8
|
14
|
20
|
35
|
50
|
Group normal min
max um
|
10
|
15
|
40
|
50
|
60
|
30
|
60
|
80
|
90
|
110
|
|
|